Why are Leveling Knives in Platen Diecutting Ineffective?

Anything you know and you would like to share out. Please put here and we will categorize your article later.

Why are Leveling Knives in Platen Diecutting Ineffective?

Postby Chris » Mon Jun 20, 2011 1:32 pm

Why are Leveling Knives in Platen Diecutting Ineffective?
By : Kevin Carey

http://www.brausse-group.com/community/download/die_cuttingworks/images/Why_are_Leveling_Knives_in_Platen_Diecutting_Ineffective/DC-2806-172x300.pnghttp://www.brausse-group.com/community/download/die_cuttingworks/images/Why_are_Leveling_Knives_in_Platen_Diecutting_Ineffective/DC-2612-300x187.pngOne of the hid­den chal­lenges fac­ing the diemaker and the diecut­ter, is the deflec­tion and dis­tor­tion of the diecut­ting press under the con­sid­er­able force required to con­vert a sub­strate into qual­ity prod­ucts with con­sis­tent per­for­mance attrib­utes. The degree of deflec­tion is related to the size of the steel rule die design/layout com­pared to the size of the press, see above right, and the loca­tion of the die, com­pared to the cen­ter of effort of the mech­a­nism. This is often char­ac­ter­ized as Cen­ter Deflec­tion and/or Off-Center Deflec­tion. See above left. Obvi­ously the pri­mary dif­fer­ence in loca­tion is based upon if the press is either a grip­per fed sub­strate sys­tem or a con­veyor fed sub­strate system.

http://www.brausse-group.com/community/download/die_cuttingworks/images/Why_are_Leveling_Knives_in_Platen_Diecutting_Ineffective/DC-3404-e1306970698827-300x189.pngTo avoid the inevitable dam­age this would cause to the steel rule die, the press, and the diecut prod­ucts the diemaker coop­er­ates with the diecut­ter to mod­ify the tools to incor­po­rate bal­anc­ing devices. These include the use of Press Stops, see right, inte­grated into the periph­ery of the steel rule die, and designed to ensure the rec­i­p­ro­cat­ing platen can only close to a spe­cific gap, between the upper and lower surfaces.

http://www.brausse-group.com/community/download/die_cuttingworks/images/Why_are_Leveling_Knives_in_Platen_Diecutting_Ineffective/DC-3405-300x281.pngA sim­i­lar tech­nique requires the inte­gra­tion of ‘Bear­ers’ into the periph­ery of the lay­out. These can be a fixed height, sim­i­lar to the press stops, or they can include the abil­ity to add or remove sev­eral adjust­ment ‘shims.See left. A com­mon alter­na­tive to using press stops and bear­ers is the use of the same height cut­ting knife, see right, to act as a press stop or a bearer, and limit the deflec­tion or dis­tor­tion of the platen mechanism.

The the­ory is, and it is impor­tant to state up front that the assump­tions made are fatally flawed and are incor­rect, that using the same stan­dard height cut­ting knife used in the die for the bearer knives, the inevitable com­pres­sive dam­age to the cut­ting knives in the steel rule die, would be matched by iden­ti­cal com­pres­sive dam­age in the bearer knives, so bal­ance across the entire platen would be main­tained. How­ever, this makes dan­ger­ous and incor­rect assump­tions.

Image


The assump­tion is the lev­el­ing knives will bal­ance and sta­bi­lize the dis­tri­b­u­tion of pres­sure to pre­vent press deflec­tion and main­tain a per­fectly par­al­lel rela­tion­ship between the platen sur­faces and the tools. Unfor­tu­nately, when you exam­ine this the­ory in detail it makes lit­tle sense. In the dia­gram above you can see the stack of com­po­nents cen­tered on the steel rule die and the stack of com­po­nents cen­tered on the lev­el­ing knives … are not the same! What is miss­ing is the thick­ness of sub­strate from the lev­el­ing knives! There­fore, this stan­dard approach to using lev­el­ing knives has min­i­mal impact on press leveling.

http://www.brausse-group.com/community/download/die_cuttingworks/images/Why_are_Leveling_Knives_in_Platen_Diecutting_Ineffective/DC-2869-e1306972757704-258x300.pngEven when the sub­strate is inte­grated into the lev­el­ing knife pat­tern, see right, we still have a seri­ous imbal­ance. This is caused by the real­ity that the die is pen­e­trat­ing and burst­ing paper­board, which sig­nif­i­cantly increases the pres­sure or resis­tance gen­er­ated by the die com­pared to the pressure/resistance gen­er­ated by the lev­el­ing knives, which are not pinch­ing and pen­e­trat­ing a substrate.

The bot­tom line is inescapable. Using Lev­el­ing Knives in the stan­dard man­ner is largely inef­fec­tive in bal­anc­ing pres­sure across the cut­ting sur­face of the platen.

The solu­tion is to com­bine Full Height Creas­ing Rule with ‘Power Ejec­tion’ tech­niques. But more on that in another article…




Source : Die Cutting-Works
Chris
 
Posts: 410
Joined: Tue Mar 31, 2009 10:12 pm

Return to Knowledge Base

Who is online

Users browsing this forum: No registered users and 5 guests

cron